RockOla 500/501 : random song trouble [SOLVED]

Tagged: random play wallbox2mp3

This topic has 19 replies, 5 voices, and was last updated 4 years, 10 months ago by Anonymous.

Viewing 19 reply threads

Author

Posts
- 28 December 2019 at 13 h 13 min #46805
  
  G.Buter
  Participant
  
  Hi all,
  
  I have bought 2 Wallbox2mp3. Both for a RockOla 500/501 wallbox.
  
  One works great. I switch on the wallbox and the wallbox2player. Altough it is configured to play only random, nothing happens. Than after I make a selection it starts to play the selected song and than it goes on playing random. Perhaps a bit strange but I like the way it works .
  
  With the other wallbox it is not possible to make an selection. So the wallbox2mp3 must be configured to play random stand-alone. Thus when I switch on the wallbox and the wallbox2mp3, it must start to play random.
  
  When I tested the second wallbox2mp3 before building in, all worked as expected. Now when I glued it in the wallbox and power it up, the wallbox2mp3 only powers on. Nothing happens now.
  
  Does anyone knows what to do so that it starts to play random again ? (a reset ?) I already tried different SD cards and formatted them again.
  
  Thanks, Gerard
- 28 December 2019 at 17 h 34 min #46806
  
  Scudie
  Participant
  
  Hi Gerard
  
  I am guessing that if it worked as you expected before you fitted it to the wallbox, it has to be that something has changed since fitting it?
  
  Why is it not possible to make a selection with the 2nd wallbox ?
  
  If you have two SD cards that are configured the same you could try swapping them. Cheers Scudie
- 28 December 2019 at 18 h 40 min #46807
  
  G.Buter
  Participant
  
  By this wallbox I need to build it in (in the other I could place the wallbox2mp3 outside the wallbox, so there I can use coins).
  
  This one (for a friend) must be build inside the wallbox. There is something wrong with the mechanisme, it’s stuck. That’s why it needs to play random (stand alone). Do you know if it still needs the 24 v AC connection besides the signal input ?
  
  That is the only difference.
  
  Gerard
- 28 December 2019 at 22 h 44 min #46808
  
  Scudie
  Participant
  
  Hi Gerard
  
  Yes I think it will require the 25vac connection, the signal is a pulsed ground if the sd is configured for random selection I would think there should be no requirement for a signal.
  
  Paul
- 29 December 2019 at 9 h 02 min #46809
  
  G.Buter
  Participant
  
  Hi Paul,
  
  I will try tomorrow. Will let you (all) know if that was/is the problem.
  
  Thanx Gerard
- 29 December 2019 at 16 h 23 min #46815
  
  Sooner
  Participant
  
  If you’re not using the wallbox to make selections then you shouldn’t need the 24v power. All you need is the 5 volt power and speakers to run the wallbox2mp3 in random play only.
  
  Strange that you need to make a selection first in one of yours to get random play started. Never heard of that problem.
- 29 December 2019 at 16 h 56 min #46816
  
  G.Buter
  Participant
  
  Yeah, strange indeed. Shall format and rebuild the SD again and see if if starts playing random (the second wallbox2mp3). But I already tried that before.
  
  First thing I thought it does not need 25 vac, that’s why I asked if someone knew if it needed (and how) a reboot.
  
  But with the reply from Paul I hoped he was right. I will let you know. Thanks for the help.
  
  Gerard
- 30 December 2019 at 12 h 19 min #46817
  
  G.Buter
  Participant
  
  Hi,
  
  Tried everything but I do not know anymore.
  
  Tried the wallbox2mp3 to start up without SD card. Just turns on but no 2 flashes that is misses the SD card.
  
  Tried with a new sdcard formatted on FAT 16kb (windows), than configured it with the program. It build the sd card with 100 selections with always play V 1.3
  
  Started the wallbox2mp3 again and still nothing (also tried with the 25vac connected).
  
  I see only 1 red light turns on (a secondred light should start after a few seconds) on the wallbox2mp3. The only conclusion I can think of is that this wallbox2mp3 is defect.
  
  If you also have no idea I shall contact retroelectronik.
  
  Thanks for your help.
  
  Gerard
- 31 December 2019 at 1 h 19 min #46820
  
  Sooner
  Participant
  
  Sounds like a defective unit. Their quality control is a bit lacking. I received 3 units recently that were defective. The first one was probably damaged because the power supply was putting out double the voltage (10 volts instead of 5). The other two had a defective audio amplifier. I’ve also heard of units with a diode installed backwards, and one where the remote volume control worked as a balance control instead. Good luck and let us know how it goes.
- 31 December 2019 at 10 h 20 min #46821
  
  Scudie
  Participant
  
  It does sound like you may have a defective unit, as Steve said there has been problems with them I had a couple with the optocoupler fitted incorrectly, they swapped them fairly promptly.
  
  Although it’s something I have never done, I guess if you are running the unit only in random play mode it would not matter about the optocoupler.
  
  Let us know how you get on.
  
  Paul
- 31 December 2019 at 12 h 13 min #46822
  Scudie
  Participant
  Forgot to ad this to previous post,
  
  Or for that matter the 25vac, as Steve pointed out.
  
  Cheers Paul
  - This reply was modified 4 years, 10 months ago by Scudie.
- 31 December 2019 at 13 h 43 min #46824
  
  G.Buter
  Participant
  
  I will contact the supplier next year :). I think it was already not good when it came out of the box.
  
  Will inform you about progress. Thanks for the help and very good and healthy 2020.
  
  Gerard
- 8 January 2020 at 16 h 18 min #46878
  
  G.Buter
  Participant
  
  Hi,
  
  Did contact retro-electronik (Gaelle). Directly a new unit was shipped to me, build it in and the problem was solved. It seems to work great with a few tests.
  
  Perfect service and thank you for your help.
  
  All the best, Gerard
- 9 January 2020 at 0 h 53 min #46879
  
  Scudie
  Participant
  
  Hello Gerard
  
  Good to hear that you are all sorted and have your project up and running now.
  
  Any photos of them?
- 9 January 2020 at 17 h 37 min #46882
  
  G.Buter
  Participant
  
  Hi, here are the 2 walboxes. This is mine. You can switch it on, its just a lamp. When you make a selection it starts and after the selected record it continues to play random. I like the way it works this way, so I leave it this way.
- 9 January 2020 at 17 h 44 min #46883
  
  G.Buter
  Participant
  
  This is the one I made for a friend (with the new unit in it). It only plays random when switching it on. That’s what he wanted. Did not need the 25 V AC connection. On my speakers the sound is very good and loud. Mine works with the internal speakers from the wallbox.
  
  He is going to place it on a post with 2 speakers you got on American drive-in cinema’s. The one’s they placed near the car.
- 9 January 2020 at 18 h 46 min #46887
  
  Klaatu
  Keymaster
  
  The bi-lingual screen is nice, that’s different, great that the importer used the same police/font as US version.
- 9 January 2020 at 21 h 56 min #46892
  
  Scudie
  Participant
  
  Hi Guys like the Rockola’s they do look the part, and the Dinosaur fuel pump,
  
  hope you have a copy of Alley Oop on it?
  
  Whats a Police / Font?
  
  Cheers Scudie
- 13 January 2020 at 16 h 36 min #46895
  
  G.Buter
  Participant
  
  Hi, Alley Oop I only got on 78 RPM. On the wallbox I like Bobby Darin “Things” most. Gr. Gerard
- 17 January 2020 at 17 h 45 min #46909
  
  Anonymous
  Inactive
  
  it’s really great Gerard 🙂
  
  I really like to see the photos of the achievements, it’s an incredible moment of sharing for us, not just sending a product 🙂 thank you
Author

Posts

Viewing 19 reply threads

You must be logged in to reply to this topic.